How do I design a circuit to convert a 100 mV and 50 Hz sine wave to a square wave? The 2019 Stack Overflow Developer Survey Results Are In Announcing the arrival of Valued Associate #679: Cesar Manara Planned maintenance scheduled April 17/18, 2019 at 00:00UTC (8:00pm US/Eastern)Triangular waveform to square waveform circuitSquare wave / Sine wave is more audibleSine wave to square wave - Schmitt triggerWhat is the best way to get a sine wave from a square wave?How to build a circuit that generates a sine wave?High-current capable (±250A) AC power-supply, sine wave/square wave (±20V)Why sine wave not square wave?Sine to Square only with a MCUHow to check (with DIY methods) if an Inverter returns a Square or a Sine Wave?Need a circuit to convert 230V sine wave into 5V square waveSine to square wave converter
Keeping a retro style to sci-fi spaceships?
What can I do if neighbor is blocking my solar panels intentionally?
What's the point in a preamp?
Why not take a picture of a closer black hole?
TDS update packages don't remove unneeded items
Am I ethically obligated to go into work on an off day if the reason is sudden?
Is this wall load bearing? Blueprints and photos attached
How did passengers keep warm on sail ships?
Can we generate random numbers using irrational numbers like π and e?
Was credit for the black hole image misappropriated?
Working through the single responsibility principle (SRP) in Python when calls are expensive
Categorical vs continuous feature selection/engineering
Mortgage adviser recommends a longer term than necessary combined with overpayments
Can I visit the Trinity College (Cambridge) library and see some of their rare books
Why can't devices on different VLANs, but on the same subnet, communicate?
How to handle characters who are more educated than the author?
Windows 10: How to Lock (not sleep) laptop on lid close?
Word to describe a time interval
Can a flute soloist sit?
Does Parliament need to approve the new Brexit delay to 31 October 2019?
What is the padding with red substance inside of steak packaging?
Is 'stolen' appropriate word?
Do I have Disadvantage attacking with an off-hand weapon?
ELI5: Why do they say that Israel would have been the fourth country to land a spacecraft on the Moon and why do they call it low cost?
How do I design a circuit to convert a 100 mV and 50 Hz sine wave to a square wave?
The 2019 Stack Overflow Developer Survey Results Are In
Announcing the arrival of Valued Associate #679: Cesar Manara
Planned maintenance scheduled April 17/18, 2019 at 00:00UTC (8:00pm US/Eastern)Triangular waveform to square waveform circuitSquare wave / Sine wave is more audibleSine wave to square wave - Schmitt triggerWhat is the best way to get a sine wave from a square wave?How to build a circuit that generates a sine wave?High-current capable (±250A) AC power-supply, sine wave/square wave (±20V)Why sine wave not square wave?Sine to Square only with a MCUHow to check (with DIY methods) if an Inverter returns a Square or a Sine Wave?Need a circuit to convert 230V sine wave into 5V square waveSine to square wave converter
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty margin-bottom:0;
$begingroup$
I have a sine wave of 100 mV and 50 Hz. I want to design a circuit that converts this sine wave into a square wave as shown in a figure.
circuit-design sine square
edited 59 mins ago
Peter Mortensen
1,60031422
asked 6 hours ago
UmangcernUmangcern
113
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
add a comment |
$begingroup$
I have a sine wave of 100 mV and 50 Hz. I want to design a circuit that converts this sine wave into a square wave as shown in a figure.
circuit-design sine square
edited 59 mins ago
Peter Mortensen
1,60031422
asked 6 hours ago
UmangcernUmangcern
113
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
$begingroup$
Possible duplicate of Triangular waveform to square waveform circuit
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
You would almost certainly want to add hysteresis to your solution for a low level low frequency application
$endgroup$
– sstobbe
6 hours ago
$begingroup$
Does the OP want a 50% duty cycle? in which case, some zero-crossing is needed.
$endgroup$
– analogsystemsrf
18 mins ago
add a comment |
$begingroup$
I have a sine wave of 100 mV and 50 Hz. I want to design a circuit that converts this sine wave into a square wave as shown in a figure.
circuit-design sine square
edited 59 mins ago
Peter Mortensen
1,60031422
asked 6 hours ago
UmangcernUmangcern
113
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
I have a sine wave of 100 mV and 50 Hz. I want to design a circuit that converts this sine wave into a square wave as shown in a figure.
circuit-design sine square
circuit-design sine square
edited 59 mins ago
Peter Mortensen
1,60031422
asked 6 hours ago
UmangcernUmangcern
113
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 59 mins ago
Peter Mortensen
1,60031422
asked 6 hours ago
UmangcernUmangcern
113
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 59 mins ago
Peter Mortensen
1,60031422
edited 59 mins ago
Peter Mortensen
1,60031422
edited 59 mins ago
Peter Mortensen
1,60031422
1,60031422
asked 6 hours ago
UmangcernUmangcern
113
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 6 hours ago
UmangcernUmangcern
113
asked 6 hours ago
UmangcernUmangcern
113
113
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Umangcern is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$begingroup$
Possible duplicate of Triangular waveform to square waveform circuit
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
You would almost certainly want to add hysteresis to your solution for a low level low frequency application
$endgroup$
– sstobbe
6 hours ago
$begingroup$
Does the OP want a 50% duty cycle? in which case, some zero-crossing is needed.
$endgroup$
– analogsystemsrf
18 mins ago
add a comment |
$begingroup$
Possible duplicate of Triangular waveform to square waveform circuit
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
You would almost certainly want to add hysteresis to your solution for a low level low frequency application
$endgroup$
– sstobbe
6 hours ago
$begingroup$
Does the OP want a 50% duty cycle? in which case, some zero-crossing is needed.
$endgroup$
– analogsystemsrf
18 mins ago
$begingroup$
Possible duplicate of Triangular waveform to square waveform circuit
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
Possible duplicate of Triangular waveform to square waveform circuit
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
You would almost certainly want to add hysteresis to your solution for a low level low frequency application
$endgroup$
– sstobbe
6 hours ago
$begingroup$
You would almost certainly want to add hysteresis to your solution for a low level low frequency application
$endgroup$
– sstobbe
6 hours ago
$begingroup$
Does the OP want a 50% duty cycle? in which case, some zero-crossing is needed.
$endgroup$
– analogsystemsrf
18 mins ago
$begingroup$
Does the OP want a 50% duty cycle? in which case, some zero-crossing is needed.
$endgroup$
– analogsystemsrf
18 mins ago
add a comment |
1 Answer
1
active
oldest
votes
$begingroup$
The easiest way to do this would be to use a comparator.
Picture taken from linked site
All you have to do is set your Vref level to where you want your square wave to trigger. When the sine wave crosses the Vref level, the comparator output will go high. As it approaches it again and goes below the Vref level, the comparator output goes low.
You will then get yourself a square wave.
Be aware the example shown in the graphic is of a non-inverting comparator. An inverting comparator works with the same principle, but the output is inverted
answered 6 hours ago
MCGMCG
6,75431850
$endgroup$
$begingroup$
The OP seems to want to cut off the negative half of the sine wave, so a diode may be needed at the input.
$endgroup$
– JimmyB
6 hours ago
1
$begingroup$
@JimmyB Not if you pick a comparator that can handle a negative input voltage.
$endgroup$
– Hearth
6 hours ago
$begingroup$
A diode for 100mV will be hard to find...
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
There are a dozen better ways to produce an accurate narrow pulse centred around a sine peak which may have noise or change in amplitude
$endgroup$
– Sunnyskyguy EE75
6 hours ago
12
$begingroup$
@SunnyskyguyEE75, yes there are. Hence why my opening line was the easiest way. Not the best way. A beginner question deserves a beginners answer. Once the OP has built up knowledge and experience, then better, but more involved ways can be looked at. There is no need to try and belittle my answer by saying there are a dozen better ways just because of what I said in the comments to the question. By all means, write your own overcomplicated answer which I am sure will be useful to more experienced engineers but useless to a beginner
$endgroup$
– MCG
6 hours ago
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Umangcern is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f432206%2fhow-do-i-design-a-circuit-to-convert-a-100-mv-and-50-hz-sine-wave-to-a-square-wa%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
The easiest way to do this would be to use a comparator.
Picture taken from linked site
All you have to do is set your Vref level to where you want your square wave to trigger. When the sine wave crosses the Vref level, the comparator output will go high. As it approaches it again and goes below the Vref level, the comparator output goes low.
You will then get yourself a square wave.
Be aware the example shown in the graphic is of a non-inverting comparator. An inverting comparator works with the same principle, but the output is inverted
answered 6 hours ago
MCGMCG
6,75431850
$endgroup$
$begingroup$
The OP seems to want to cut off the negative half of the sine wave, so a diode may be needed at the input.
$endgroup$
– JimmyB
6 hours ago
1
$begingroup$
@JimmyB Not if you pick a comparator that can handle a negative input voltage.
$endgroup$
– Hearth
6 hours ago
$begingroup$
A diode for 100mV will be hard to find...
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
There are a dozen better ways to produce an accurate narrow pulse centred around a sine peak which may have noise or change in amplitude
$endgroup$
– Sunnyskyguy EE75
6 hours ago
12
$begingroup$
@SunnyskyguyEE75, yes there are. Hence why my opening line was the easiest way. Not the best way. A beginner question deserves a beginners answer. Once the OP has built up knowledge and experience, then better, but more involved ways can be looked at. There is no need to try and belittle my answer by saying there are a dozen better ways just because of what I said in the comments to the question. By all means, write your own overcomplicated answer which I am sure will be useful to more experienced engineers but useless to a beginner
$endgroup$
– MCG
6 hours ago
add a comment |
$begingroup$
The easiest way to do this would be to use a comparator.
Picture taken from linked site
All you have to do is set your Vref level to where you want your square wave to trigger. When the sine wave crosses the Vref level, the comparator output will go high. As it approaches it again and goes below the Vref level, the comparator output goes low.
You will then get yourself a square wave.
Be aware the example shown in the graphic is of a non-inverting comparator. An inverting comparator works with the same principle, but the output is inverted
answered 6 hours ago
MCGMCG
6,75431850
$endgroup$
$begingroup$
The OP seems to want to cut off the negative half of the sine wave, so a diode may be needed at the input.
$endgroup$
– JimmyB
6 hours ago
1
$begingroup$
@JimmyB Not if you pick a comparator that can handle a negative input voltage.
$endgroup$
– Hearth
6 hours ago
$begingroup$
A diode for 100mV will be hard to find...
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
There are a dozen better ways to produce an accurate narrow pulse centred around a sine peak which may have noise or change in amplitude
$endgroup$
– Sunnyskyguy EE75
6 hours ago
12
$begingroup$
@SunnyskyguyEE75, yes there are. Hence why my opening line was the easiest way. Not the best way. A beginner question deserves a beginners answer. Once the OP has built up knowledge and experience, then better, but more involved ways can be looked at. There is no need to try and belittle my answer by saying there are a dozen better ways just because of what I said in the comments to the question. By all means, write your own overcomplicated answer which I am sure will be useful to more experienced engineers but useless to a beginner
$endgroup$
– MCG
6 hours ago
add a comment |
$begingroup$
The easiest way to do this would be to use a comparator.
Picture taken from linked site
All you have to do is set your Vref level to where you want your square wave to trigger. When the sine wave crosses the Vref level, the comparator output will go high. As it approaches it again and goes below the Vref level, the comparator output goes low.
You will then get yourself a square wave.
Be aware the example shown in the graphic is of a non-inverting comparator. An inverting comparator works with the same principle, but the output is inverted
answered 6 hours ago
MCGMCG
6,75431850
$endgroup$
The easiest way to do this would be to use a comparator.
Picture taken from linked site
All you have to do is set your Vref level to where you want your square wave to trigger. When the sine wave crosses the Vref level, the comparator output will go high. As it approaches it again and goes below the Vref level, the comparator output goes low.
You will then get yourself a square wave.
Be aware the example shown in the graphic is of a non-inverting comparator. An inverting comparator works with the same principle, but the output is inverted
answered 6 hours ago
MCGMCG
6,75431850
answered 6 hours ago
MCGMCG
6,75431850
answered 6 hours ago
MCGMCG
6,75431850
answered 6 hours ago
MCGMCG
6,75431850
6,75431850
$begingroup$
The OP seems to want to cut off the negative half of the sine wave, so a diode may be needed at the input.
$endgroup$
– JimmyB
6 hours ago
1
$begingroup$
@JimmyB Not if you pick a comparator that can handle a negative input voltage.
$endgroup$
– Hearth
6 hours ago
$begingroup$
A diode for 100mV will be hard to find...
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
There are a dozen better ways to produce an accurate narrow pulse centred around a sine peak which may have noise or change in amplitude
$endgroup$
– Sunnyskyguy EE75
6 hours ago
12
$begingroup$
@SunnyskyguyEE75, yes there are. Hence why my opening line was the easiest way. Not the best way. A beginner question deserves a beginners answer. Once the OP has built up knowledge and experience, then better, but more involved ways can be looked at. There is no need to try and belittle my answer by saying there are a dozen better ways just because of what I said in the comments to the question. By all means, write your own overcomplicated answer which I am sure will be useful to more experienced engineers but useless to a beginner
$endgroup$
– MCG
6 hours ago
add a comment |
$begingroup$
The OP seems to want to cut off the negative half of the sine wave, so a diode may be needed at the input.
$endgroup$
– JimmyB
6 hours ago
1
$begingroup$
@JimmyB Not if you pick a comparator that can handle a negative input voltage.
$endgroup$
– Hearth
6 hours ago
$begingroup$
A diode for 100mV will be hard to find...
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
There are a dozen better ways to produce an accurate narrow pulse centred around a sine peak which may have noise or change in amplitude
$endgroup$
– Sunnyskyguy EE75
6 hours ago
12
$begingroup$
@SunnyskyguyEE75, yes there are. Hence why my opening line was the easiest way. Not the best way. A beginner question deserves a beginners answer. Once the OP has built up knowledge and experience, then better, but more involved ways can be looked at. There is no need to try and belittle my answer by saying there are a dozen better ways just because of what I said in the comments to the question. By all means, write your own overcomplicated answer which I am sure will be useful to more experienced engineers but useless to a beginner
$endgroup$
– MCG
6 hours ago
$begingroup$
The OP seems to want to cut off the negative half of the sine wave, so a diode may be needed at the input.
$endgroup$
– JimmyB
6 hours ago
$begingroup$
The OP seems to want to cut off the negative half of the sine wave, so a diode may be needed at the input.
$endgroup$
– JimmyB
6 hours ago
1
1
$begingroup$
@JimmyB Not if you pick a comparator that can handle a negative input voltage.
$endgroup$
– Hearth
6 hours ago
$begingroup$
@JimmyB Not if you pick a comparator that can handle a negative input voltage.
$endgroup$
– Hearth
6 hours ago
$begingroup$
A diode for 100mV will be hard to find...
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
A diode for 100mV will be hard to find...
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
There are a dozen better ways to produce an accurate narrow pulse centred around a sine peak which may have noise or change in amplitude
$endgroup$
– Sunnyskyguy EE75
6 hours ago
$begingroup$
There are a dozen better ways to produce an accurate narrow pulse centred around a sine peak which may have noise or change in amplitude
$endgroup$
– Sunnyskyguy EE75
6 hours ago
12
12
$begingroup$
@SunnyskyguyEE75, yes there are. Hence why my opening line was the easiest way. Not the best way. A beginner question deserves a beginners answer. Once the OP has built up knowledge and experience, then better, but more involved ways can be looked at. There is no need to try and belittle my answer by saying there are a dozen better ways just because of what I said in the comments to the question. By all means, write your own overcomplicated answer which I am sure will be useful to more experienced engineers but useless to a beginner
$endgroup$
– MCG
6 hours ago
$begingroup$
@SunnyskyguyEE75, yes there are. Hence why my opening line was the easiest way. Not the best way. A beginner question deserves a beginners answer. Once the OP has built up knowledge and experience, then better, but more involved ways can be looked at. There is no need to try and belittle my answer by saying there are a dozen better ways just because of what I said in the comments to the question. By all means, write your own overcomplicated answer which I am sure will be useful to more experienced engineers but useless to a beginner
$endgroup$
– MCG
6 hours ago
add a comment |
Umangcern is a new contributor. Be nice, and check out our Code of Conduct.
Umangcern is a new contributor. Be nice, and check out our Code of Conduct.
Umangcern is a new contributor. Be nice, and check out our Code of Conduct.
Umangcern is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f432206%2fhow-do-i-design-a-circuit-to-convert-a-100-mv-and-50-hz-sine-wave-to-a-square-wa%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
$begingroup$
Possible duplicate of Triangular waveform to square waveform circuit
$endgroup$
– Eugene Sh.
6 hours ago
$begingroup$
You would almost certainly want to add hysteresis to your solution for a low level low frequency application
$endgroup$
– sstobbe
6 hours ago
$begingroup$
Does the OP want a 50% duty cycle? in which case, some zero-crossing is needed.
$endgroup$
– analogsystemsrf
18 mins ago